home *** CD-ROM | disk | FTP | other *** search
- 1 Name idenfying the connection in Directory.
- 2 Type of virtual circuit for X.25 or Frame Relay PSN.
- 3 Indicates whether remote Router is Eicon or 3rd party.
- 4 Number of the EiconCard port to be used.
- 5 Indicates whether Local or Remote will initiate the connection.
- 6 If checked on, connection will start at bootup.
- 7 Seconds of inactivity before a Two-Way connection is suspended.
- 9 Number of times Router should try to establish a connection.
- 10 Delay in seconds between retry attempts.
- 11 Enables support of IP protocol.
- 12 Enables support of IPX protocol.
- 13 Enables support of AppleTalk protocol.
- 14 IP address of the remote router.
- 15 Obtain this number from your X.25 subscription.
- 16 Obtain this number from personnel at remote site.
- 17 This may contain country-specific information, or a password.
- 18 User Facilities on your X.25 subscription.
- 19 User Facilities on your X.25 subscription.
- 20 Number of permanent virtual circuits (PVCs) for the connection.
- 21 Data Link Connection Identifier from your Frame Relay subscription.
- 22 This comment will appear on the console with your connection information.
- 23 Enables support of IP, IPX, AppleTalk protocols.
- 24 Enables IP protocol broadcasts.
- 25 LU name of local STG node.
- 26 LU name of remote SNA network node.
- 27 Name of mode level for session communication.
- 28 Local pace window size.
- 29 Remote pace window size.
- 30 Node name.
- 49 Network ID.
- 50 Name assigned to the local network node.
- 51 Network ID.
- 52 Name assigned to the remote network node.
- 53 Connection information summary.
- 54 Filter out packets for this application.
- 55 Name of primary associated with present Backup
- 56 Type or Rip Sap Update
- 57 Type of connection Primary/Backup
- 58 Enable/Disable Segment configuration
- 59 Enable/Disable X ID
- 60 Enter value for Rip Delay
- 61 Enter value for Rip Delay
- 62 The number of port
- 63 The unique name of port
- 64 Enter the node is a unique (12 digits HEX from 000000000001 to FFFFFFFFFFFE)
- 65 Enter the number of connection range is 1 to 64
- 66 Enter the IP address (000.000.000.000) 0 to 255.
- 67 Enter the IPX address (8 digits HEX from 00000001 to FFFFFFFE)
- 68 Enter Apple talk Net range is (1 to 65279) the range delta must be 0 or positive
- 69 Enter Apple talk Net range is (1 to 65279) the range delta must be 0 or positive
- 70 Select if you want bind yes or no
- 71 Select if you want compress yes or no
- 72 Enter the text zone with comma separator
- 73 Select an item inside list box
- 74 Enter the IP mask (000.000.000.000) 0 to 255.
- 75 Enable/Disable IPX WAN Support.
- 76 Enable/Disable sending Inverse ARP to discover the remote IP Address.
- 77 Choose the Compression Negotiation.
- 78 Choose the Compression Algorithm to use.
- 79 Choose the compression dictionary size.
- 80 TDB --- Comp_Check_Ext
- 81 TDB --- Comp_Check_Seq
- 82 TDB --- Comp_Check_LCB
- 83 Number of configured connections in the routing table.
- 84 Number of configured IP filters in the routing table.
- 85 Maximum number of connections that will load.
- 86 Maximum number of supported IP filters.
- 87 Number of NCBs that will be transmitted per Port.
- 88 Port through which data flows between local and remote devices.
- 89 Maximum number of bytes per data packet transmitted -- must match remote.
- 90 The IP address of the remote device.
- 91 The IP address Subnet mask.
- 92 The default Gateway of the device.
- 93 When checked, the peer router supplies the MAC Address. Valid for PPP connections only.
- 94 The remote MAC Address. Valid for PPP connections only.
-